New Year Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: 70special

Examstrust Logo
examstrust mcafee
  1. Home
  2. Checkpoint
  3. CCME
  4. 156-835 - Check Point Certified Maestro Expert

Checkpoint 156-835 Check Point Certified Maestro Expert Exam Practice Test

Page: 1 / 6
Total 64 questions
Get 156-835 Full Access Download 156-835 PDF

Check Point Certified Maestro Expert Questions and Answers

Testing Engine

  • Product Type: Testing Engine
$37.5  $124.99
Add to Cart

PDF + Testing Engine

  • Product Type: PDF + Testing Engine
$52.5  $174.99
Add to Cart

PDF Study Guide

  • Product Type: PDF Study Guide
$33  $109.99
Add to Cart
Question 1

What is the throughput penalty of Security Group?

Options:

A.

5% per member

B.

Depends on the type of Appliance

C.

10% per Security Group with no relation to amount of members

D.

1% per member

Question 2

How many power supplies are presented on MHO-140?

Options:

A.

2

B.

4

C.

1

D.

1 with option for 2

Question 3

In order to set Site (chassis) priority per VS, following command should be used:

Options:

A.

From given VS context: set chassis high-availability vs chassis_priority

B.

From given VSO context: set chassis high-availability vs chassis_priority

C.

From any VS context: set chassis high-availability vs chassis_priority

D.

From VSO context: set chassis high-availability vs chassis_priority

Question 4

What is the basic installation sequence of the Orchestrator in case of single Orchestrator?

1. Create a Security Group

2. Configure Default Gateway

3. Connect with Serial Console cable to the Orchestrator

4. Configure IP for one of its Management interfaces

5. Connect an appliance to a downlink port

6. Change Orchestrator amount to 1

7. Browse to the Orchestrator’s WebUI

Options:

A.

3-4-2-6-5-7-1

B.

3-1-7-2-4-6-5

C.

1-4-2-5-7-3-6

D.

7-4-2-5-3-1-6

Question 5

What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?

Options:

A.

Three cables: uplink, downlink, SYNC

B.

One Downlink cable only

C.

Two cables: one uplink and one downlink

D.

Four cables: uplink, downlink, SYNC and Management

Question 6

What cannot be a reason for DETACHED status of Appliance when runningasg monitorcommand?

Options:

A.

Appliance reboots

B.

Appliance is a member of Security Group, but currently disconnected

C.

Appliance installed with R80.20

D.

There's an issue with Downlink cable

Question 7

What is the difference between Dual-Site and Multi-Room?

Options:

A.

Multi-Room is a Single-Site deployment where all Appliances are connected to both orchestrators

B.

Multi-Room is a kind of Dual-Site deployment within the same building

C.

Multi-Room is Active / Standby and Dual-Site is Active / Active

D.

This is the same

Question 8

Which command will be used in order to restart Orchestrator service only?

Options:

A.

orchd restart

B.

cpstop; cpstart

C.

reboot

D.

service orchestrator restart

Question 9

What is the Iterator process?

Options:

A.

Iterator is the process that simulates distribution in case of Appliance failure

B.

Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive

C.

Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure

D.

Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery

Load More 156-835 Questions
Page: 1 / 6
Total 64 questions
Get 156-835 Full Access Download 156-835 PDF